Alert Type
SRN - Software Release Notification
Risk
Risk Description
Low/Notification
Software Release Notification
Impact
Impact Description
Low/Notification
Software Release Notificaiton
Product Affected
ACX PTX QFX running Junos Evolved Software
Alert Description
Junos Software Service Release version 21.3R3-S5-EVO is now available for download from the Junos software download site
Download Junos Software Service Release:
Go to
Junos Platforms - Download Software page
Input your product in the "Find a Product" search box
From the Type/OS drop-down menu, select
Junos SR
From the Version drop-down menu, select your version
Click the Software tab
Select the Install Package as need and follow the prompts
Solution
Junos Software service Release version 21.3R3-S5-EVO is now available.
21.3R3-S5-EVO - List of Fixed issues
PR Number
Synopsis
Category: AFT l2lam
1721704
Sending GARP reply packet on a VTEP interface causes flooding in network on QFX5130 and QFX5700 platforms
Product-Group=evo
On Junos OS Evolved QFX5130 and QFX5700 platforms, Gratuitous Address Resolution Protocol (GARP) flooding occurs in the network when it receives a GARP reply packet on a Virtual Tunnel End Point (VTEP) interface.
PR Number
Synopsis
Category: Border Gateway Protocol
1679495
RV task replication will be stuck in the "NotStarted" state when routing-options validation is deactivated/activated
Product-Group=evo
On all Junos and Junos Evolved platforms with Non-Stop Routing (NSR) enabled, in a rare case, Route Validation (RV) task replication will be stuck in the "NotStarted" state when routing-options validation is deactivated/activated.
1709837
Junos OS and Junos OS Evolved: A crafted BGP UPDATE message allows a remote attacker to de-peer (reset) BGP sessions (CVE-2023-4481)
Product-Group=evo
An Improper Input Validation vulnerability in the Routing Protocol Daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated, network-based attacker to cause a Denial of Service (DoS). Please refer to https://supportportal.juniper.net/
JSA72510
[juniper.net]
for more information.
1728455
The rpd process crashes when BGP is cleaned up
Product-Group=evo
On Junos and Junos OS Evolved platforms, if static default RT-C (Route Target -Constrain) is configured when Border Gateway Protocol (BGP) is cleaned up (whole BGP is cleaned up), the routing process will crash.
1728604
Traffic impact is seen when there is a single peer in the proxy BGP group connected to the BGP route reflector
Product-Group=evo
On all Junos and Junos OS Evolved platforms, if the proxy BGP (Border Gateway Protocol) route reflector is connected to the only peer present in the BGP group then it stops advertising the routes coming from the remote cluster and that leads to proxy route-target routes not getting added which causes traffic disruption.
1732493
The rpd process crash will be observed with BMP and independent resolution is enabled for secondary BGP routes
Product-Group=evo
On all Junos and Junos OS Evolved platforms, when BMP (BGP Monitoring Protocol) post-policy and independent resolution is enabled for secondary (route leaked through rib-group) BGP routes, then with the inactive secondary route change the rpd process crash will be observed.
1732833
Constant BGP peer flaps would core rpd
Product-Group=evo
On all Junos and Junos OS Evolved platforms , rpd (Routing Protocol Daemon) soft cores can be seen if BGP (Border Gateway protocol) peer session flaps constantly. It is non Service impacting issue.
1736029
Junos OS and Junos OS Evolved: RPD crash when attempting to send a very long AS PATH to a non-4-byte-AS capable BGP neighbor (CVE-2023-44186)
Product-Group=evo
An Improper Handling of Exceptional Conditions vulnerability in AS PATH processing of Juniper Networks Junos OS and Junos OS Evolved allows an attacker to send a BGP update message with an AS PATH containing a large number of 4-byte ASes, leading to a Denial of Service (DoS). Please refer to https://supportportal.juniper.net/
JSA73150
[juniper.net]
for more information.
1739335
The rpd process crash will be observed when the prefix-limit exceeds on the backup RE
Product-Group=evo
On all Junos and Junos OS Evolved platforms configured with BGP (Border Gateway Protocol), NSR (Nonstop Active Routing), and prefix-limit with idle-timeout, when the prefix-limit exceeds on the backup RE (Routing Engine) and switchover is performed the rpd process crash will be observed on the new backup RE.
1739919
Junos OS and Junos OS Evolved: A BGP session will flap upon receipt of a specific, optional transitive attribute (CVE-2023-0026)
Product-Group=evo
An Improper Input Validation vulnerability in the Routing Protocol Daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated, network-based attacker to cause a Denial of Service (DoS). Please refer to https://supportportal.juniper.net/
JSA71542
[juniper.net]
for more details.
1745073
CPU in rpd spikes and scheduler slips will be observed when the duplicate community is added
Product-Group=evo
On all Junos and Junos Evolved platforms, when Border Gateway Protocol (BGP) is configured with the existing community member added via another community that is called in import policy and the intermediate router does not support large/extended communities based on scale (route). Due to this, the rpd Central Processing Unit (CPU) stays high and protocols level choking will be seen in adjacent nodes. Scheduler slips are also observed due to the same.
PR Number
Synopsis
Category: Issues related to EVO interface statistics.
1748236
Child interfaces deleted from AE interfaces are still shown as part of AE
Product-Group=evo
On all Junos OS Evolved platforms, child interfaces deleted from AE (Aggregated Ethernet) interfaces are still shown as part of AE. This is a display issue and seen only when interface statistics for the AE interface is cleared within a few seconds of deactivating/deleting the child members. There is no impact on traffic.
PR Number
Synopsis
Category: software upgrade infra issues
1731877
Auto-sw-sync doesn't trigger upgrade/restart of routing engine
Product-Group=evo
On Junos Evolved PTX10008 and PTX10016 platforms, on releases after 21.2R1-EVO, on enabling auto-sw-sync with no user groups configuration, routing engine 1 (RE1) after joining the cluster, can not sync the versions present in master RE0.
PR Number
Synopsis
Category: EVO Netstack Juniper Tunnel Driver Module
1713989
Junos OS Evolved: Packets which are not destined to the router can reach the RE (CVE-2023-44195)
Product-Group=evo
An Improper Restriction of Communication Channel to Intended Endpoints vulnerability in the NetworkStack agent daemon (nsagentd) of Juniper Networks Junos OS Evolved allows an unauthenticated network based attacker to cause limited impact to the availability of the system. Please refer to https://supportportal.juniper.net/
JSA73160
[juniper.net]
for more information.
PR Number
Synopsis
Category: Issues related to NTP issues on evo
1729126
Junos OS and Junos OS Evolved: Multiple NTP vulnerabilities resolved
Product-Group=evo
Multiple NTP vulnerabilities have been resolved in Juniper Networks Junos OS and Junos OS Evolved by updating third-party software where vulnerabilities were found during external security research. Please note that there is no ability within the CLI to perform any exploitation for these issues. Only shell allows sending ntpq queries to remote systems. Please refer to https://supportportal.juniper.net/
JSA73177
[juniper.net]
for more information.
PR Number
Synopsis
Category: EVO Socket replication
1732611
BGP/MACsec(key-chain) configuration applied from Netconf causes VMcore on Junos OS Evolved platforms
Product-Group=evo
On all Junos OS Evolved platforms, VMcores are seen when MACsec (Media Access Control Security) key-chains and BGP(Border Gateway Protocol) configurations are applied through Netconf.
PR Number
Synopsis
Category: PRs related to tunnels like GRE, IPIP in EVO control plane
1717782
Traffic loss is observed with FTI over IRB as underlay.
Product-Group=evo
In case of FTI (Flexible Tunnel Interface) over IRB (Integrated Routing and Bridging) over ethernet, underlay ifl (logical interface) was pointing to IRB instead of ethernet interface leading to packet loss.
PR Number
Synopsis
Category: EVPN control plane issues
1716663
RPD process crash may be observed when routing or evo-pfemand process is restarted and multicast snooping process adds a route to inetmcsn.1 table
Product-Group=evo
On Junos OS Evolved platforms, a routing process crash may be observed when "restart routing" or "restart evo-pfemand" is applied and multicast snooping process adds a route to inetmcsn.1 table at the same time. When the issue is hit, the core file of rpd will be generated. This is a timing issue and it may be observed when both the events happen at the same time.
1723832
The rpd core is seen in the long-running devices with EVPN enabled
Product-Group=evo
On Junos and Junos Evolved platforms, BGP (Border Gateway Protocol) community object reference count is not handled properly during the process of remote BGP peer routes update event. The community reference count is increasing during the increment function. However, decrement functions are not called in one of the places after processing the routes update. This will lead to a disturbance of the continuity reference count, which will cause an rpd crash.
1739686
Evpn-vxlan comp nh is not installed in pfe after peer reboot
Product-Group=evo
Evpn-vxlan comp nh is not installed in pfe after reboot.
PR Number
Synopsis
Category: EVPN Layer-2 Forwarding
1758677
MAC addresses programming failure resulting in traffic flooding
Product-Group=evo
Issue 1: On QFX5K and EX platforms in the VXLAN (Virtual Extensible LAN) environment, traffic flooding will be observed for MAC addresses not getting programmed in the hardware with VPLAG (Virtual Chassis Port Link Aggregation) configured and BGP (Border Gateway Protocol) flaps. This issue happens when hardware programming by L2ALM to PFE fails, and during re-sync, SVLBNH (shared VXLAN load balancing next hop) info is not sent to PFE/hardware. Issue 2: On all Junos and Junos Evolved platforms, l2alm sends a delete request for control MAC addresses to l2ald after multiple hardware sync failures.
PR Number
Synopsis
Category: jdhcpd daemon
1714260
The DHCPv4 relay will send two option-82 to the server and the DHCP session will not be established
Product-Group=evo
On all Junos and Junos OS Evolved platforms, when Dynamic Host Configuration Protocol (DHCPv4) Relay is configured with forward-only mode along with "trust-option-82", DHCP-relay should not add another option 82 to the packet sent to the DHCP server. The DHCP server upon receiving the packet with two option-82 will respond only with 1st header of option-82 which might get dropped by the relay, thus the packet is not forwarded to the DHCP client and the DHCP session won't get established.
1722082
DHCP binding is not happening in EVPN VXLAN topology with DHCP stateless relay (forward-only)
Product-Group=evo
In EVPN VXLAN topology with DHCP stateless relay (forward-only) configured at layer 3 gateways, Jdhcpd broadcasts snooped unicast offer packets. That leads to the offer getting dropped on its way to the client and then the IP negotiation fails.
PR Number
Synopsis
Category: Layer 2 Control Module
1720521
Junos OS and Junos OS Evolved: Multiple Vulnerabilities in CLI command (CVE-2023-44177)
Product-Group=evo
A Stack-based Buffer Overflow vulnerability in the CLI command of Juniper Networks Junos and Junos EVO allows a low privileged attacker to execute a specific CLI commands leading to Denial of Service. Repeated actions by the attacker will create a sustained Denial of Service (DoS) condition. Please refer to https://supportportal.juniper.net/
JSA73140
[juniper.net]
for more information.
1739975
Layer 2 traffic will be dropped on VSTP disabled interface
Product-Group=evo
On Junos platforms, Whenever an interface is disabled under VSTP (VLAN Spanning Tre Protocol) configuration, the issue will be seen in the following cases. 1. When interface, IFBD (Interface Family Bridge Domain) and VSTP, configured via single commit. (In case of new configuration) 2. When VSTP configurations are present and chassisd restarts/device reboots, then issue will be seen. (During ifd delete and add, issue will be seen)
1763053
LLDP neighborship will not be formed on all Junos devices
Product-Group=evo
On Junos and Junos OS Evolved platforms, LLDP (Link Layer Discovery protocol) neighborship will not come up on local device if the local device is using Junos version lower than 22.3 and remote device is using Junos version 21.4R3-S2 and its subsequent service releases or version higher than 22.3.
PR Number
Synopsis
Category: lacp protocol
1609618
LACP Member interfaces might get stuck in out of sync state
Product-Group=evo
When sync-reset feature is enabled on the device then few member interfaces might stay in out of sync state even when number of available child interfaces is greater than minimum-links configured for the Lag interface. This will affect the overall capacity of the lag interface.
PR Number
Synopsis
Category: OSPF routing protocol
1737978
OSPFv3 using the VIP address on the IRB interface will not form adjacencies between peers
Product-Group=evo
OSPFv3 may not form adjacencies on IRB interfaces with VRRP configuration.
PR Number
Synopsis
Category: Protocol Independant Multicast
1720708
Slow convergence of PIM joins causes temporary traffic loss with scaled downstream interfaces
Product-Group=evo
On all Junos and Junos Evolved platforms with PIM (Protocol Independent Multicast), MVPN (Multicast Virtual Private Network) configured and when the number of downstream interfaces is more than three thousand, slow convergence of PIM joins is seen to take up more of the time and CPU, causing traffic loss for some time.
PR Number
Synopsis
Category: QFX5100 Interface related issues
1688023
The LLDP output packets are not transmitting on the em0 interface of Junos and Junos OS Evolved platforms
Product-Group=evo
On Junos and Junos OS Evolved platforms, if a management Ethernet interface(em0) has an inet or inet6 family configured and "delete interfaces em0" is issued, the Link Layer Discovery Protocol (LLDP) output packets will stop transmitting, causing the LLDP neighborship to remain down in peer router.
PR Number
Synopsis
Category: RPD infrastructure issues related to NSR, GRES, switchover,
1727957
The traffic drop is observed during the Graceful restart on Junos and Junos Evolved platforms
Product-Group=evo
On all Junos and Junos Evolved platforms, during the time of Graceful restart(GR), the routes in the Multiprotocol Label Switching(mpls).0 table will be updated even when the routing protocols are in the process of re-convergence and have not yet come out of GR. This causes inaccurate routes in the routing table and traffic drop is observed during GR.
PR Number
Synopsis
Category: RPD route tables, resolver, routing instances, static routes
1746439
Route-distinguisher change leads to the route being present in rpd, but not installed in kernel/PFE
Product-Group=evo
On Junos and Junos Evolved platforms, traffic impact will be observed when route-distinguisher change is performed for which route will be present in rpd, but not installed in kernel/PFE. This issue happens when the aggregate route is configured.
PR Number
Synopsis
Category: Resource Reservation Protocol
1703424
Pathtear message is not forwarded by PLR to merge point which is causing data plane blackholing
Product-Group=evo
On all Junos and Junos OS Evolved platforms, the PLR (point of local repair) is not sending the pathtear message when the merge point supports the enhanced FRR while the route reaching the neighbor is using a shortcut route under MVPN (Multicast Virtual Private Network) configured scenario.
PR Number
Synopsis
Category: Issues related to control plane security
1719603
EVO devices may lose remote access in certain scenarios
Product-Group=evo
In Junos OS Evolved, the xinetd config file was not updated correctly. This could lead to a situation where external login services (such as SSH, NETCONF over SSH, or Telnet) were not accessible. Due to a software defect, an internal function deleted the files required for SSH based services, eg "xinetd-external.conf". Thus services like SSH or Netconf will stop working In some cases when a box was booting, the "xinetd-external.service" came up before the initial boot-time MGD commit would create the file. This caused the service to come up without a config file. Since remote login over may be disabled: SSH Telnet NETCONF over SSH NETCONF over TLS so you may need to log in via the serial console. Following error will be observed in the system: xinetd[6588]: open( /etc/xinetd-external.conf ) failed: No such file or directory (errno = 2) xinetd[6588]: 6588 {init_services} couldn't get configuration. Exiting... xinetd[7537]: xinetd Version 2.3.15 started with libwrap options compiled in. xinetd[7537]: Started working: 2 available services
PR Number
Synopsis
Category: Bug and Review Tracking for Segment routing traffic eng
1737119
The traffic blackhole will be observed when the SRTE shortcut is configured
Product-Group=evo
On Junos platforms, when the MPLS (Multiprotocol Label Switching) packet reaches the destination router, it will have a label that is unknown to the destination router due to a label POP operation miss at the ingress router resulting in the traffic black hole in the scenario SR-MPLS (Segment Routing With Multiprotocol Label Switching) + traffic engineering shortcut is configured.
PR Number
Synopsis
Category: Configuration mgmt, ffp, load-action, commit processing
1562848
The mustd process may crash on all platforms
Product-Group=evo
With a large-scale configuration, in rare cases, the mustd process might crash. The mustd process, which is responsible for configuration constraint checks, might crash on commit, leading to commit failure.
1659783
The configuration might roll back after performing "commit confirmed" and then reboot
Product-Group=evo
On all Junos OS and Junos OS Evolved platforms, the configuration might roll back after performing "commit confirmed" and then a reboot.
1663590
Commit failure might be observed on reactivation or commit of specific configurations after the upgrade of the device
Product-Group=evo
On all Junos and Junos Evolved platforms, reactivation or commit of specific configurations fails after the upgrade of the device.
PR Number
Synopsis
Category: UI Infrastructure - mgd, DAX API, DDL/ODL
1693630
In JUNOS EVO "show | display inheritance" does not work correctly for LSPs with whitespace in the name
Product-Group=evo
An LSP with whitespace in the name does not display correctly when viewing the configuration using 'show | display inheritance'
1730336
The rpd crashes and the commit operation fails while pushing a large configuration with the "extend-size" option enabled
Product-Group=evo
On all Junos platforms, when the 'extend-size' option is configured and a scaled configuration is committed, the rpd process crashes and the commit operation fails.
1740289
The 'load replace' operation might result in mustd and mgd crash
Product-Group=evo
On Junos and Junos Evolved platforms with 'apply-group' configured, the mustd and mgd processes might crash when the 'load replace' operation is performed. When this happens, 'apply-groups' will get deleted internally and the respective hierarchies will not be notified.
1745565
The mgd process crash is observed when 'show' is executed from the configuration mode
Product-Group=evo
On all Junos platforms, when 'show' is executed from the configuration mode, a mgd process crash is observed which has no functionality impact.
PR Number
Synopsis
Category: Virtual Router Redundancy Protocol
1697394
VRRP Master session on AE ifl having child links on Satellite Device stops transmission post GRES
Product-Group=evo
On Junos Fusion Aggregation Device platforms, when the VRRP (Virtual Router Redundancy Protocol) interface is configured on IRB (Integrated Routing and Bridging) with underlying L2 interface on Satellite Device post GRES (graceful Routing Engine switchover) VRRP Master stops transmission of VRRP PDU (Protocol Data Unit) resulting in VRRP Master/Master state.
PR Number
Synopsis
Category: Express ZX PFE L3 Features
1652623
The AE interface will be down when strict mode rpf-check is configured
Product-Group=evo
On PTX10001-36MR, PTX10003, PTX10004, PTX10008, and PTX10016, configuring (Unicast Reverse Path Forwarding) rpf-check strict mode on the (Aggregated Ethernet) AE interface brings down the AE interface resulting in traffic loss.
21.3R3-S5-EVO - List of Known issues
PR Number
Synopsis
Category: DNX L2 related features
1756648
The evo-pfemand process is observed to crash on Junos Evolved platforms with LACP configuration
Product-Group=evo
JDI_REG:EVO:ultron: evo-pfemand.re cored at futex_abstimed_wait_cancelable (private=0, abstime=0x7fd17582c870, clockid=0, expected=0, futex_word=0x7fd1479fb570) at ../sysdeps/unix/sysv/linux/futex-internal.h:208
Resolved In:
evo:23.4R1-EVO evo:24.1R1-EVO
PR Number
Synopsis
Category: mgd, ddl, odl infra issues
1607134
XML namespace in some command outputs has a character between the version and the "limited" keyword
Product-Group=evo
On all Junos Evolved platforms, When limited encryption junos image is used, the XML namespace in some command outputs has a character between the version and the "limited keyword. Because of this XML parsers (like the one in Python/PyEZ) is not parsing the XML output. There is no traffic impact.
Resolved In:
evo:20.4R3-EVO evo:21.1R3-S3-EVO evo:21.2R3-S2-EVO evo:21.3R3-S2-EVO evo:21.4R1-EVO junos:21.4R1
1665008
The system will ask for password while saving configuration files on single RE platforms
Product-Group=evo
The system may ask for your password when you are thing to save configuration file.
Resolved In:
evo:22.3X50-EVO evo:22.4R3-EVO evo:23.1R1-EVO junos:23.1R1
PR Number
Synopsis
Category: SNMP, mib2d issues
1704878
Neighbor device details not listed under snmp walk [ipNetToMediaPhysAddress]
Product-Group=evo
On Junos Evolved platforms, SNMP walk table (ipNetToMediaPhysAddress) is not updated when a neighbour entry is configured.
Resolved In:
evo:21.4R3-S6-EVO evo:22.3X50-EVO evo:22.3X80-D38-EVO evo:22.3X80-D39-EVO evo:23.1R2-EVO evo:23.2R1-EVO evo:23.4R1-EVO evo:23.4R2-EVO
PR Number
Synopsis
Category: PTX10K Diagnostics related PRs
1725658
Enabling Cell BIST Support for LC1201 and LC1202 new HBM components
Product-Group=evo
With the new HBM component, a software upgrade is needed to support the new hardware for the LC1201, LC1202. (See
TSB71797
[juniper.net]
)
Resolved In:
evo:22.1R3-S3-EVO evo:22.2R3-S1-EVO evo:22.3R3-EVO evo:22.3X50-EVO evo:22.3X80-D35-EVO evo:22.4R2-S1-EVO evo:22.4R3-EVO evo:23.1R1-S1-EVO evo:23.1R2-EVO evo:23.2R1-EVO evo:23.3R1-EVO junos:22.4R3 junos:23.1R2 junos:23.2R1 junos:23.3R1
PR Number
Synopsis
Category: UI Infrastructure - mgd, DAX API, DDL/ODL
1638847
The mustd process crash might be observed with persist-group-inheritance
Product-Group=evo
On all Junos and Junos Evolved platforms configured with persist-group-inheritance, which is enabled by default from 19.4R3 onwards, might lead to mustd process crash in highly scaled configuration.
Resolved In:
evo:22.3X50-EVO evo:22.4R2-EVO evo:22.4R3-EVO evo:23.1R2-EVO evo:23.2R1-EVO junos:20.3X75-D52 junos:20.4R3-S8 junos:21.2R3-S6 junos:21.2X32-D20 junos:21.3R3-S5 junos:21.4R3-S4 junos:22.1R3-S3 junos:22.2R3-S1 junos:22.3R2-S1 junos:22.3R3 junos:22.4R2 junos:22.4R3 junos:23.1R1-S1 junos:23.1R2 junos:23.2R1
1656565
Commit and commit check fails when the knob "interface-range" is configured
Product-Group=evo
On all Junos and Junos Evolved platforms, when the knob "interface-range" is configured commit and commit check fails.
Resolved In:
evo:21.2R3-S7-EVO evo:21.4R2-S2-EVO evo:21.4R3-EVO evo:22.1R1-S2-EVO evo:22.1R2-EVO evo:22.2R1-S1-EVO evo:22.2R2-EVO evo:22.4R1-EVO junos:21.4R2-S2 junos:21.4R3 junos:22.1R1-S2 junos:22.1R2 junos:22.2R1-S1 junos:22.3R1 junos:22.4R1
1706285
Junos OS and Junos OS Evolved: High CPU load due to specific NETCONF command (CVE-2023-44184)
Product-Group=evo
An Improper Restriction of Operations within the Bounds of a Memory Buffer vulnerability in the management daemon (mgd) process of Juniper Networks Junos OS and Junos OS Evolved allows a network-based authenticated low-privileged attacker, by executing a specific command via NETCONF, to cause a CPU Denial of Service to the device's control plane. Please refer to https://supportportal.juniper.net/
JSA73147
[juniper.net]
for more information.
Resolved In:
evo:21.4R3-S4-EVO evo:22.1R3-S2-EVO evo:22.2R2-J4-EVO evo:22.2R2-S2-J1-EVO evo:22.2R3-EVO evo:22.3R3-EVO evo:22.3X50-EVO evo:22.3X80-D35-EVO evo:22.3X80-D36-EVO evo:22.4R2-EVO evo:22.4R3-EVO evo:23.1R2-EVO evo:23.2R1-EVO junos:19.1R3-S10 junos:19.2R3-S7 junos:19.3R3-S8 junos:19.4R3-S12 junos:20.2R3-S8 junos:20.3X75-D36 junos:20.3X75-D44 junos:20.4R3-S7 junos:20.4R3-S8 junos:21.2R3-S5 junos:21.2X32-D20 junos:21.3R3-S5 junos:21.4R3-S4 junos:22.1R3-S2 junos:22.2R3 junos:22.3R2-S1 junos:22.3R3 junos:22.4R1-S2 junos:22.4R2 junos:22.4R3 junos:23.1R1 junos:23.1R1-S1 junos:23.1R2 junos:23.2R1
PR Number
Synopsis
Category: Issues related to NETCONF
1585855
< ok/> response is getting generated along with < rpc-error>
Product-Group=evo
When maximum-password-length is configured and the user tries to configure password whose length exceeds configured maximum-password-length, there is an error and the '' tag is emitted. (Ideally '' tag should not be emitted in an error scenario.) The configuration does not get committed.
Resolved In:
evo:22.2R3-S1-EVO evo:22.3R2-S2-EVO evo:22.4R3-EVO evo:23.1R1-EVO evo:23.2R1-EVO junos:20.3X75-D36 junos:22.2R3-S1 junos:22.3R2-S2 junos:22.3R3-S1 junos:22.4R2-S2 junos:22.4R3 junos:23.1R1 junos:23.2R1
Modification History
First publication 2023-12-26
21.3R3-S5-EVO: Software Release Notification for JUNOS Evolved Software