Q> Is lean-edge default on ACX7020?
lean-edge
Ans > Yes supported
Q> Is cloud-metro supported?
cloud-metro
Ans > yes
Q> Is carrier-ethernet supported?
carrier-ethernet
Ans > No it is not
Q> Is bng supported?
bng
Can you please help confirm these questions below and send documents to support this?
1) Is "lean-edge" default profile
2) How to verify which is the current/active profile rather than "show configuration" for checking
3) Is profile "carrier-ethernet" available on ACX7020, if so, how to enable it
4) Given that ACX7020 is used as Metro ethernet switch doing Layer2 switching, QinQ, Vlan operations...There is no requirement for EVPN/VXLAN/MPLS/VRF. Which profile is the correct for this use case?
labroot@jtac-acx7020-r2001> start shell user root
Password:
[vrf:none] root@jtac-acx7020-r2001:~# vty fpc0
root@jtac-acx7020-r2001:pfe> show evo-pfemand mdb-info
User Config : Profile:lean-edge Kaps:1
Max possible mac limit for this profile:85000
Ans > Default Profile is lean-edge
TableName Type Capacity EntrySize
=================================================
TCAM 0 0
KAPS1 KAPS (LPM) 1572864 0
KAPS2 KAPS (LPM) 65536 0
ISEM1 Exact Match 65536 30
ISEM2 Exact Match 81920 30
ISEM3 Exact Match 65536 30
INLIF1 Direct Access 65536 60
INLIF2 Direct Access 32768 60
INLIF3 Direct Access 32768 60
IVSI Direct Access 21846 90
LEM Exact Match 393216 30
IOEM1 Exact Match 49152 30
IOEM2 Exact Match 65536 30
MAP Direct Access 0 0
FEC1 Direct Access 32768 150
FEC2 Direct Access 26215 150
FEC3 Direct Access 32768 150
PPMC Exact Match 98304 30
GLEM1 Exact Match 65536 30
GLEM2 Exact Match 65536 30
EEDB1 EEDB 32768 0
EEDB2 EEDB 32768 0
EEDB3 EEDB 32768 0
EEDB4 EEDB 32768 0
EEDB5 EEDB 16384 0
EEDB6 EEDB 16384 0
EEDB7 EEDB 16384 0
EEDB8 EEDB 16384 0
EOEM1 Exact Match 32768 30
EOEM2 Exact Match 49152 30
ESEM Exact Match 65536 30
EVSI Direct Access 32768 30
SEXEM1 Exact Match 65536 30
SEXEM2 Exact Match 0 0
SEXEM3 Exact Match 0 0
LEXEM Exact Match 131072 30
RMEP_EM Exact Match 65536 30
root@jtac-acx7020-r2001:pfe> exit
Ans > Yes it is. Now if you want to change lean-edge to cloud-metro
Then, Apply below
root@jtac-acx7020-r2001# set system packet-forwarding-options hw-db-profile cloud-metro
[edit]
root@jtac-acx7020-r2001# show | compare
+ system {
+ packet-forwarding-options {
+ hw-db-profile {
+ cloud-metro;
+ }
root@jtac-acx7020-r2001# commit check
configuration check succeeds
Post doing it PFE would be re-initialized
PFE initialization is not completed yet, please wait...!
User Config : Profile:cloud-metro Kaps:1
Max possible mac limit for this profile:270000
KAPS1 KAPS (LPM) 917504 0
ISEM2 Exact Match 49152 30
ISEM3 Exact Match 49152 30
INLIF2 Direct Access 65536 60
INLIF3 Direct Access 65536 60
LEM Exact Match 1245184 30
IOEM2 Exact Match 49152 30
FEC1 Direct Access 26215 150
FEC2 Direct Access 13108 150
FEC3 Direct Access 26215 150
PPMC Exact Match 65536 30
EEDB7 EEDB 0 0
EEDB8 EEDB 0 0
EOEM2 Exact Match 32768 30
ESEM Exact Match 49152 30
EVSI Direct Access 16384 30
The only difference i see is the MAC limit difference in both the profiles lean-edge has 85000 whereas cloud-metro has 270,000
Where as if you try to change it then below options are listed, doing so will restart the PFE as I demonstrated above
root@jtac-acx7020-r2001# set system packet-forwarding-options hw-db-profile ?
Possible completions:
+ apply-groups Groups from which to inherit configuration data
+ apply-groups-except Don't inherit configuration data from these groups
cloud-metro Selects Cloud-Metro DB profile, restarts PFE
lean-edge Selects Lean Edge max IPv4/IPv6 FIB DB profile, restarts PFE
srv6-scale Selects SRv6 VPN SID scale DB profile, restarts PFE